Effect of Shot Peening Parameters on PLA Parts Manufactured with Fused Deposition Modeling
DOI:
https://doi.org/10.5614/j.eng.technol.sci.2023.55.5.1Keywords:
3D printing, fused deposition modelling, post processing, printing parameter, shot peeningAbstract
Fused deposition modeling (FDM) is a technology with potential benefits such as material versatility, user-friendliness, and cost-effectiveness. However, the mechanical properties of FDM-printed specimens are relatively low. To address this issue, post-processing techniques such as shot peening can be employed. Shot peening is utilized as a post-treatment for metal-based and ABS materials, but its application to PLA material has not been explored yet. This study aimed to evaluate the effect of shot peening on the mechanical properties of FDM-printed PLA samples. A full factorial experimental design was employed with shot peening speed, duration, and number of outer shells as parameters. The tensile strength of 72 samples after the shot peening process was measured and evaluated. Analysis of variance (ANOVA) revealed that all parameters had a significant influence on tensile strength. Additionally, the interaction of speed*time and speed*number of shells also had a significant influence. Meanwhile, the interaction of time*number of shells and speed*time*number of shells had no significant influence. The findings of this study demonstrate the potential of post-processing techniques to enhance the mechanical strength of FDM components, particularly those composed of PLA material.
Downloads
References
Wang, P., Zou, B. & Ding, S., Modeling of Surface Roughness Based on Heat Transfer Considering Diffusion among Deposition Filaments for FDM 3D Printing Heat-Resistant Resin, Applied Thermal Engineering, 161, 114064, 2019.
Penumakala, P.K., Santo, J. & Thomas, A., A Critical Review on the Fused Deposition Modeling of Thermoplastic Polymer Composites, Composites Part B: Engineering, 201, pp. 108336-108336, 2020.
Chac, J.M., Caminero, M.A., Nez, P.J., Garcia-Plaza, E., Garcia-Moreno, I. & Reverte, J.M., Additive Manufacturing of Continuous Fibre Reinforced Thermoplastic Composites Using Fused Deposition Modelling: Effect of Process Parameters on Mechanical Properties, Composites Science and Technology, 181, pp. 107688-107688, 2019.
Liu, Z., Wang, Y., Wu, B., Cui, C., Guo, Y. & Yang, C., A Critical Review of Fused Deposition Modeling 3D Printing Technology in Manufacturing Polylactic Acid Parts, International Journal of Advanced Manufacturing Technology, 102(9-12), pp. 2877-2889, 2019.
Behzadnasab, M., Yousefi, A.A., Ebrahimibagha, D. & Nasiri, F., Effects of Processing Conditions on Mechanical Properties of Pla Printed Parts, Rapid Prototyping Journal, 26(2), pp. 381-389, 2020.
Lee, H.W., Insyani, R., Prasetyo, D., Prajitno, H. & Sitompul, J.P., Molecular Weight and Structural Properties of Biodegradable PLA Synthesized with Different Catalysts By Direct Melt Polycondensation, Journal of Engineering and Technological Sciences, 47(4), pp. 364-373, 2015.
Simangunsong, D.I., Hutapea, T.H.A., Lee, H.W., Ahn, J.O. & Sitompul, J.P., The Effect of Nanocrystalline Cellulose (NCC) Filler on Polylactic Acid (PLA) Nanocomposite Properties, Journal of Engineering and Technological Sciences, 50(4), pp. 578-587, 2018.
Laziz, A.A., Mazlan, N., Yusoff, M.Z.M. & Ariff, A.H.M., Investigation of Alkaline Surface Treatment Effected on Flax Fibre Woven Fabric with Biodegradable Polymer Based on Mechanical Properties, Journal of Engineering and Technological Sciences, 52(5), pp. 677-690, 2020.
Ikada, Y., Biodegradable Polymers as Scaffolds for Tissue Engineering, Handbook of Biodegradable Polymers, pp. 341-362, 2011.
Grare, A., Guduric, V., Bareille, R., Heroguez, V., Latour, S., L'heureux, N., Fricain, J.C., Catros, S. & Le Nihouannen, D., Characterization of Printed PLA Scaffolds for Bone Tissue Engineering, Journal of Biomedical Materials Research Part A, 106(4), pp. 887-894, Apr. 2018.
Rajeshkumar, G., Seshadri, S.A., Devnani, G., Sanjay, M.R., Siengchin, S., Maran, J.P., Al-Dhabi, N.A., Karuppiah, P., Mariadhas, V.A., Sivarajasekar, N. & Anuf, A.R., Environment Friendly, Renewable and Sustainable Poly Lactic Acid (PLA) Based Natural Fiber Reinforced Composites?A Comprehensive Review, Journal of Cleaner Production, 310, 127483, 2021.
Brischetto, S., Ferro, C.G., Torre, R. & Maggiore, P., 3D FDM Production and Mechanical Behavior of Polymeric Sandwich Specimens Embedding Classical and Honeycomb Cores, Curved and Layered Structures, 5(1), pp. 80-94, 2018.
Lalehpour, A., Janeteas, C. & Barari, A., Surface Roughness of FDM Parts After Post-Processing with Acetone Vapor Bath Smoothing Process, International Journal of Advanced Manufacturing Technology, 95(1?4), pp. 1505?1520, 2018.
Heidari-rarani, M., Rafiee-afarani, M. & Zahedi, A., Mechanical Characterization of FDM 3D Printing of Continuous Carbon Fiber Reinforced PLA Composites, Composites Part B: Engineering, 175, 107147, 2019.
Morampudi, P., Venkata Ramana, V.S.N., Bhavani, K., Amrita, M. & Srinivas, V., The Investigation of Machinability and Surface Properties of Aluminium Alloy Matrix Composites, Journal of Engineering and Technological Sciences, 53(4), 210412, 2021.
Kumar mishra, P., Ponnusamy, S. &Reddy Nallamilli, M.S., The Influence of Process Parameters on the Impact Resistance of 3D Printed PLA Specimens Under Water-Absorption and Heat-Treated Conditions, Rapid Prototyping Journal, 27(6), pp. 1108-1123, 2021.
Wang, P., Zou, B., Ding, S., Li, L. & Huang, C., Effects of FDM-3D Printing Parameters on Mechanical Properties and Microstructure of CF/PEEK and GF/PEEK, Chinese Journal of Aeronautics, 34(9), pp. 236-246, 2021.
Colpani, A., Fiorentino, A. & Ceretti, E., Characterization of Chemical Surface Finishing with Cold Acetone Vapours on ABS Parts Fabricated by FDM, Production Engineering, 13, pp. 437-447, 2019.
Nsengimana, J., Van der Walt, J., Pei, E. & Miah, M., Effect of Post-Processing on the Dimensional Accuracy of Small Plastic Additive Manufactured Parts, Rapid Prototyping Journal, 25(1), pp. 1-12, 2019.
Ge, J., Pillay, S., Ning, H., Post-Process Treatments for Additive-Manufactured Metallic Structures: A Comprehensive Review, Journal of Materials Engineering and Performance, 32(16), pp. 7073-7122, Aug. 2023.
Bagherifard, S., Beretta, N., Monti, S., Riccio, M., Bandini, M. & Guagliano, M., On the Fatigue Strength Enhancement of Additive Manufactured Alsi10mg Parts by Mechanical and Thermal Post-Processing, Materials & Design, 145, pp. 28-41, 2018.
?ebrowski, R., Walczak, M., Korga, A., Iwan, M. & Szala, M., Effect of Shot Peening on the Mechanical Properties and Cytotoxicity Behaviour of Titanium Implants Produced By 3D Printing Technology, Journal of Healthcare Engineering, 2019, e8169538, Dec. 2019.
Bagherifard, S., Hickey, D.J., Fintov S., Pastorek, F., Fernandez-Pariente, I., Bandini, M., Webster, T.J. & Guagliano, M., Effects of Nanofeatures Induced by Severe Shot Peening (SSP) On Mechanical, Corrosion and Cytocompatibility Properties of Magnesium Alloy AZ31, Acta Biomaterialia, 66, pp. 93-108, 2018.
Soyama, H., Comparison between the Improvements Made to the Fatigue Strength of Stainless Steel by Cavitation Peening, Water Jet Peening, Shot Peening and Laser Peening, Journal of Materials Processing Technology, 269, pp. 65-78, Jul. 2019.
Arifvianto, B., Mahardika, M., Salim, U.A. &Suyitno, Comparison of Surface Characteristics of Medical-Grade 316L Stainless Steel Processed by Sand-Blasting, Slag Ball-Blasting and Shot-Blasting Treatments, Journal of Engineering and Technological Sciences, 52(1), pp. 1-13, 2020.
Maamoun, A.H., Elbestawi, M.A. & Veldhuis, S.C., Influence of Shot Peening on Alsi10mg Parts Fabricated by Additive Manufacturing, Journal of Manufacturing and Materials Processing, 2(3), 40, 2018.
Kahlin, M., Ansell, H., Basu, D., Kerwin, A., Newton, L., Smith, B. & Moverare, J.J., Improved Fatigue Strength of Additively Manufactured Ti6Al4V by Surface Post Processing, International Journal of Fatigue, 134, 105497, May 2020.
Kanger, C., Hadidi, H., Akula, S., Sandman, C., Quint, J., Alsunni, M., Underwood, R., Slafter, C., Sonderup, J., Spilinek, M., Casias, J., Rao, P. & Sealy, M.P., Effect of Process Parameters and Shot Peening on Mechanical Behavior of ABS Parts Manufactured by Fused Filament Fabrication (FFF), Solid Freeform Fabrication 2017: Proceedings of the 28th Annual International Solid Freeform Fabrication Symposium - An Additive Manufacturing Conference, SFF 2017, (August), pp. 444-458, 2020.
