Analisis Produktivitas Hydraulic Static Pile Driver Pada Pembangunan Apartemen Victoria Square Tower B Tangerang Banten

Arif Rahman Hakim, Amirul Akbar

Abstract


Abstrak

Dalam membangun suatu konstruksi apartemen diperlukan perhatian dalam pelaksanaan konstruksinya, terutama pada pekerjaan pemancangan. Lokasi pembangunan Apartemen Victoria Square Tower B Tangerang Banten terletak di lingkungan perumahan dan memiliki keterbatasan ruang gerak, sehingga diperlukan solusi terkait pengerjaan pemancangan tersebut agar tidak menimbulkan getaran/kebisingan terhadap lingkungan sekitar. Dalam studi kasus pembangunan Apartemen Victoria Square Tower B Tangerang Banten, metode pemancangan yang digunakan adalah menggunakan alat Hydraulic Static Pile Driver. Jenis-jenis pekerjaan pada pemancangan tersebut terdiri dari Move to The Point, Lifting Pile, Clamping & Piling, Joint Pile (Welding), Dolly, dan Cutting Pile. Hasil analisis deskriptif pada penelitian ini didapat nilai produksi alat Hydraulic Static Pile Driver terendah adalah 0.225 meter/menit atau setara 13.5 meter/jam dan nilai produksi tertinggi adalah 1.364 meter/menit atau setara 82 meter/jam.

Abstract

In building an apartment construction requires attention in the construction implementation, especially in the erection work. The construction location of Victoria Square Apartment Tangerang Tower B Banten is located in a residential area and has limited mobility, so a solution related to the erection work is needed so as not to cause vibration/noise to the surrounding environment. In the case study of the construction of the Victoria Square Tower B Tangerang Banten Apartment, the erection method used was using a Hydraulic Static Pile Driver. The types of work in the erection consist of Move to The Point, Lifting Pile, Clamping & Piling, Joint Pile (Welding), Dolly, and Cutting Pile. The results of the descriptive analysis in this study obtained the lowest production value of Hydraulic Static Pile Driver is 0.225 meters/minute or equivalent to 13.5 meters/hour and the highest production value is 1.364 meters/minute or equivalent to 82 meters/hour.

 


Keywords


Apartemen, Hydraulic Static Pile Driver, Nilai Produksi.

Full Text:

PDF

References


Andayana, A., 2016, Analisis Perbandingan Daya Dukung Tiang Pancang Berdasarkan Uji SPT Dan Daya DUkung Tiang Pancang Berdasarkan Alat HSPD 120 T, Lampung: Universitas Lampung.

Bowles, J., 1996, Foundation Analysis and Design, Fifth Edition. Singapore: The McGraw-Hill Companies, Inc.

BPP [Berdikari Pondasi Perkasa], 2009, Retrieved September 26, 2017, from http://www.ptbppid.com/services.html

Chan, R., 2006, Foundation Design and Construction, Geo Publication No.1.

Limanto, S., 2009, Analisis Produktivitas Pemancangan Tiang Pancang Pada Bangunan Tinggi Apartemen. Seminar Nasional 2009 (pp. 293-305), Surabaya: Jurusan Teknik Sipil FT-UKM.

Pertiwi, D., 2006, Korelasi Daya Dukung Pondasi Tiang Pancang Dengan Menggunakan Data-Data Sondir dan Jack in Pile, Jurnal Aksial, Vol.8, No.1 , 36-42.

Peurifoy, R., Schexnayder, C. J., & Shapira, A., 2006, Construction Planning, Equipment, and Methods. New York: Seventh Edition, McGraw-Hill.

Tan, S. M., & Ling, C. H., 2001, The Use of High Capacity Hydraulic Injection Piles for Buildings in Limes-Stone Ex-Tin Mining Sites in Kuala Lumpur. Proceeding, 14th SEAGC. Hong Kong.

Warsito, J. Y., & Hatmoko, J. U., 2016, Pemodelan Produktivitas Hydraulic Static Pile Driver Menggunakan Model Analitis Pada Tanah Berlanau. JEMIS Vol.4 No.2 , 175-184.

White, D., Finlay, T., Bolton, M., & Bearss, G., 2002, Press-in Piling: Ground Vibration and Noise During Pile Installation. ASCE Special Publication Vol.116 , 363-371.




DOI: http://dx.doi.org/10.5614%2Fjts.2018.25.2.3

Refbacks

  • There are currently no refbacks.


web
analytics

Lisensi Creative Commons

This work is licensed under a Creative Commons Attribution-NoDerivatives 4.0 International License