Analysis of Stress State of Bolts under Different Anchorage Qualities
DOI:
https://doi.org/10.5614/j.eng.technol.sci.2018.50.3.8Keywords:
anchor bolt, anchoring defect, anchoring quality, pull-out test, stress characteristicsAbstract
A series of pull-out tests were conducted in order to study the stress states of bolts under different anchorage qualities and to simulate the influence of quality defects in empty-slurry and low-strength mortar anchorage in actual engineering. The tests mainly investigated strain characteristics at different positions of the bolts and the effects of strains at the same positions under different anchorage conditions. The research led to the following conclusions: (1) under ultimate bearing capacity, the strain values decayed the fastest along the length of the bolt in the full-length anchorage, the strain values decayed the slowest in the empty-slurry and low-strength mortar anchorage, and the decaying speed of strains in the empty-slurry mortar anchorage was between that of the above two kinds of anchorages; (2) at almost 50% of the ultimate bearing capacity, the strain values were slightly different between the empty-slurry and low-strength mortar anchorage and the empty-slurry anchorage. Obvious differences in strain values occurred when the bolts were continued to be loaded. The strain values of the full-length anchorage bolts were different from those of the other two kinds of anchorages; (3) from the analysis of stress variation characteristics, the safety reserve was the highest for the full-length anchorage under the condition of ultimate bearing capacity, followed by the empty-slurry mortar anchorage, while the safety reserve was the lowest for the empty-slurry and low-strength mortar anchorage. However, in terms of uniformity of force and utilization of the material, the result was reverse.Downloads
References
Hou, C.J. & Gou, P.F., Strengthening Mechanism of Surrounding Rock of Roadway with Bolt Support, Chinese Journal of Rock Mechanics and Engineering, 19(3), pp. 342-345, 2000.
Du, Z., Qin, B. & Tian, F., Numerical Analysis of the Effects of Rock Bolts on Stress Redistribution around a Roadway, International Journal of Mining Science & Technology, 26(6), pp. 975-980, 2016.
Zhong, Z.B., Lei, L.V. & Deng, R.G., Mechanical Analysis of Wholly Grouted Bolt Considering Axial Distribution along the Bars, Journal of Disaster Prevention and Mitigation Engineering, 33(3), pp. 311-315, 2013.
You, C.A., Analysis of Full-length Bonded Anchor Rods, Chinese Journal of Rock Mechanics and Engineering, 19(3), pp. 339-341, 2000.
Li, C. & Stillborg, B., Analytical Models for Rock Bolts, International Journal of Rock Mechanics & Mining Sciences, 36(36), pp. 1013-1029, 1999.
Jalalifar, H., An Analytical Solution to Predict Axial Load Along Fully Grouted Bolts in an Elasto-plastic Rock Mass, Journal of the Southern African Institute of Mining and Metallurgy, 111(11), pp. 809-814, 2011.
Zeng, X.M., Fan, J.Q. & Li, S.M., Experimental Study on Interfacial Shear Stress Interactions of Anchored Structures, Prestress Technology, (3), pp. 22-27, 2008.
Chen, G.F. & Mi, H.Z., Experimental Analysis of Anchor's Stress Performance in Collapsible Loess Layer, Journal of Gansu University of Technology, 29(1), pp. 116-119, 2003.
Hao, J.B., Men, Y.M. & Zhan, C.H., Model Test on the Behavior of Soil Anchor and the Influence of Water, Journal of Xi'an University of Science and Technology, 30(1), pp. 8-62, 2010.
Fang, Z., Liang, D. & Jiang, T., Experimental Investigation on the Anchorage Performance of CFRP Tendon in Different Bond Mediums, China Civil Engineering Journal, 39(6), pp. 47-51, 2006.
Wu, Y.Z., Kang, H.P. & Ding, J., Development and Application of Ultrahigh-heat Processed Rock Bolts, Journal of China Coal Society, 40(2), pp. 308-313, 2015.
Qian, D., Shimada, H. & Sasaoka, T., Stability of Roadway in Upper Seam of Deep Multiple Rich Gas Coal Seams through Ascending Stress-relief Mining, Memoirs of the Faculty of Engineering Kyushu University, 75(2), pp. 59-80, 2015.
Kang, H., Wu, Y. & Gao, F., Mechanical Performances and Stress States of Rock Bolts under Varying Loading Conditions, Tunnelling & Underground Space Technology, 52, pp. 138-146, 2016.
Li, C.C., A New Energy-absorbing Bolt for Rock Support in High Stress Rock Masses, International Journal of Rock Mechanics & Mining Sciences, 47(3), pp. 396-404, 2010.
Wang, Z.H. & Liu, Y.T., Stress Mechanism and Performance Characteristics of Bolt in Different Anchorage Modes, Mining and Metallurgical Engineering, 14(2), pp. 17-21, 1994.
Kalfat, R., & Al-Mahaidi, R., Improvement of FRP-to-concrete Bond Performance Using Bidirectional Fiber Patch Anchors Combined with FRP Spike Anchors, Composite Structures, 155, pp. 89-98, 2016.
Yang, J.H., Guo, Z.Q., & Wan, R.H., Application of Tunnel Anchorage and Anchor Bolt in Anchorage System of Wanzhou Changjiang River Bridge, Highway, 1, pp. 40-43, 2002.
Chesnokov, A.V. & Kosonogova, L.G., Prospects of Application and Constructive Features of Rubber-air Reinforced Lining, Scientific Bulletin of National Mining University, 1, pp. 39-44, 2013.
Gu, S.C., Chen, X. & Ye, G.F., Stress Distribution of Anchorage Section of Prestressed Rock Bolt Considering the Shearing Slip Effect of Grout-Rock Interface, Mining R&D, 30(2), pp. 34-36+93, 2010.
Ding, J., Yan, Z.X. & Guo, R.J., Analysis of Anchorage Characteristics and Parameter Influence of Soil Imperfect Anchor, Journal of Central South University(Science and Technology), 43(8), pp. 3209-3215, 2012.
